Saturday, February 4, 2017
We took apart an Evora shifter system to see if our shiftR111 might work. Lotus does a nice job of integrating various requirements to really drive down the cost of a component. This shifer housing clearly serves a few different functions. The key was that the overall height of the shifter and the mounting points at the front would work for our shiftR111. It appeared with a change to our hand brake brackets, we could create a shifter kit for the Evora. So we got to work on a design.
Shown below is our design for the Evora. We are now getting a prototype made to test fit into a car. We remain overtly optimistic. 8^)
We have already sorted out shifter cables and our innovative ESWkit for the Evora so a shiftR111 will complete the package nicely.
Tuesday, January 17, 2017
|2nd Gear synchro|
|rebuilt and ready to go in|
The trans has stock gears, clutch/fly and no LSD. The car was also equipped with our new shiftR111 and SMOOTHoperator but no short-shift kit. We debated internally whether or not to run a short shift kit and ultimately decided not to have it installed. We knew that the 'feel' of these new synchros would be important and anything that might influence feel would be another variable.
We ran on the 3.6mile Fittipaldi course. This configuration uses 2nd,3rd,4th &5th gears. There are some really fast sections and plenty of slow 2nd gear corners - with a couple of them heavy breaking zones. Proper heel and toe downshifts are critical on many of the corners so it was a good test of the synchros.
|a fast course with plenty of shifting from high speeds/rpms|
Overall the car shifted nicely. The feel was immediate and frankly crisp. The down shifts were great and even at times when I did not get enough of a blip, they seemed to engage really well. I drove the car on the 'street' a bit around the shop and grounds of SMMR. Again the shifting was nice and confirmed that it can work fine on street cars - with no negatives,
|taking a slight breather between sessions|
David@Synchrotech referred to synchros as the brakes for gears. As it turns out, there are many manufacturers who use synchros of this type for 15+ years. Our kit uses brass, carbon and construction that have been refined by Synchrotech over several generations - mostly in Honda applications. This is especially important to us as the Honda run 9k rpm trans that are similar to our 8k rpm gearboxes. Essentially, the carbon can deal with high speeds far better than just the brass - as found on our stock synchros. David did change the design slightly from stock to improve performance and my testing confirms that these changes are acceptable. If you compare them side by side with a stock set, you may see some differences. Our trans rebuilder, Jeff@Transaxle, was also duly impressed with the kit. His opinion was key as he rebuilds many, many gearboxes for Lotus Cup racers.
I believe they are suitable for road & track. The stock brass synchros are the weak link in the Toyota gearbox so these bits will be very welcome and will extend the life of the gearboxes. Of course, you still need to heel and toe your downshifts! Yes, these will allow for faster shifts but we still suggest clients be smooth and gentle.
We are going to get production products and release these parts. You can find them: HERE
Monday, January 9, 2017
We just pulled a clutch out of a 50k mile Evora S that was completely used up. If you look closely, you can see that the heads of the rivets are ground away; there was nothing left of this thing. It also damaged the flywheel and scored it badly enough that it also needs to be replaced.
|Delay valve shown|
The CLUTCHline will allow the clutch to engage as quickly as possible, preventing excessive slipping. It will also allow you to modulate the clutch in low speed situations rather than fight the delay valve. Of course if you want to do high RPM clutch dumps, you are going to put more stress on your transmission, but if you drive with some skill and care, the reliability of your transmission should not be compromised but your clutch life should be greatly extended. This is a good thing considering that a clutch replacement requires powertrain removal and takes roughly 40 hours of labor...
The lines are available on our site HERE. It takes about 2 hrs to install it.
Monday, January 2, 2017
We recruited a couple of long-time Lotus owners who have run countless track miles on their Lotus cars. I wanted to get their objective opinions about our new shifter. Watch the video below:
Our next step is to confirm fitment into a stock Elise, finalize the reverse lock-out cable length and then kick off production. Yes!
Monday, December 26, 2016
We're still employing the same basic mechanism as the first gen design but have taken out several machined pieces. One area that was simplified was the reverse lockout mechanism. Our Gen 1 used several machined parts that we ultimately deemed unnecessary. In fact, we also chose to reuse the factory reverse collar in the Gen2. We still need to spec in the final cable length to validate the operation but that will be quite simple - compared to most everything else!
Additionally this new design allows the factory center console to fit completely. We know that some clients would prefer to keep their cars looking stock. But we also know that many clients would like to have our shiftR111 exposed. We will be designing a simple bracket that will hold the Emergency Flasher, Lock and TC buttons.
The shifter feels nice and smooth with throws that are similar to stock. The LETSLA kit we installed on the Gen 1 version allowed us to shorten the distance to our preferred throw. We will install it into this Gen 2 after we have completed our track testing. Street testing has been great as the shifting is predictable and smooth. Heel and toe downshifts have been great.
We head to the track later this week to start testing. I'll recruit some Lotus owners to drive her as well to add to our findings.
Watch the video below:
Thursday, December 1, 2016
As discussed all across the internet (including in this BLOG), and in fine books and pamphlets all over, fastener torque is critical to the strength of any joint. Also, the torque applied to a bolt is not the critical bit. What is critical is the amount a bolt is stretched (stained) when it is installed (ever wonder why rod bolts in an engine are not just torqued, but measured?). A torque value is just a handy way to measure and apply a set amount of strain. The torque value for a fastener is calculated by estimating things like the friction factor between the fastener and its mating part, or experimentally where strain is measured for a specific application and the torque required is noted.
When working on cars here, we often see studs that have obviously not been properly torqued. Usually this means they are WAY too tight and this happens for 3 main reasons:
- Use of an impact gun
- Torquing hot wheels
- Stud lubrication
|Leave this tool in your box |
when working on your sports car.
The first most common mistake is that people put wheels on with an impact gun, this crime is committed most often (oddly enough) by wheel/tire shops. You would think that people that specialize in putting wheels on cars would do the task correctly, but they do not. It is such common practice to just buzz the lug nuts/studs/whatever on that no one bats an eye. If you are using an impact gun, how do you know that the torque is correct? Too much torque puts too much strain on the stud and the wheel itself, worst case, the stud snaps. Too little torque actually puts too much strain on the stud as well and severely lowers its fatigue life. Worst case, stud snaps. Nothing good has ever happened after a wheel stud failure. We NEVER use an impact to install wheels here. We also never use one to remove wheels either. Using an impact is hard on the wheel lugs/nuts and doing it by hand with a breaker bar allows you to feel if something is not right (over/under torqued, bad threads, etc.)
2. Torquing Hot Wheels
The second most common offense? The habit of torquing wheels right after a track session. In this scenario, the wheel studs and everything else associated with the hub are pretty hot, hot enough to change the strain in the system. So sometimes you can turn the bolt a little bit farther with the same amount of torque. You have now tightened the bolt further than you did initially (when it was cold), and now when everything cools back down, the bolt is strained more that originally intended. We think that this is minor but we still never recommend torquing hot wheels.
For peace of mind, you can check for loose bolts but wait till the wheels have cooled before checking torque. Do it just before your session starts.
3. Stud Lubrication
The third reason why wheel bolts get over torqued is lubrication of wheel studs. As mentioned early, the torque applied to a threaded fastener is meant to produce an ideal amount of pre-stress or strain in the fastener. Most of the force (torque) applied to a fastener (about 90%) while you were tightening it is not stretching the bolt, it is overcoming the friction between the two mating threads as well as the friction generated under the head of the bolt. So then the amount of friction between the parts is critical in determining the correct torque to produce a given strain. The friction can vary wildly depending on the bolt plating, thread class, materials, and lubrication. Most torque values given by manufactures are for dry threads unless stated otherwise. So if you have a torque spec for a dry thread, then you lube it with something like anti-seize or thread locker, you are going to reduce the friction and you will end up with much more strain in the fastener for the same amount of torque applied. If a fastener does not call for lubrication, it is usually best not to lube it.
So if all these mistakes are being made and people are over torquing the hell out of wheels all the time, why aren't wheels flying off cars and people dying in fiery crashes 24/7? Safety factors. Engineers always design things with a safety factor and make things able to withstand loads usually 2-10 times higher than what is expected (air craft and race car engineers usually use safety factors under 2 to reduce weight). This covers things like over torquing, misuses, accidents, etc. However, the wise (wo)man respects the safety factor she is given and does not try to push his luck. Wheel studs CAN and DO fail from improper torque.
1)Torque your studs/bolts/lug nuts with a torque wrench and according to the manufacture's specifications.
2)Tighten your lug nuts in a criss-cross or star pattern for even torque with a torque wrench
3)Check your wheel torque at least twice a day at the track - when the wheels are cold. We like to check before every session.
4)Use a torque wrench (was repetitive enough?)
Monday, November 14, 2016
|Standard bump stop on a |
Nitron 40mm Single Adjustable Shock
The bump stop prevents damage by absorbing and dissipating a huge amount of force when your suspension bottoms out. If the bump stop was not present, a large (and harsh) impact force would be transferred into the chassis and into the lower suspension arm. In this scenario, the chassis and/or the a-arm can be damaged. In other words, not good. You can have a bottom out condition without damage but it is still highly stressful to all the components and passengers involved.
The second, and more subtle job of the bump stop is to be progressive. When the car is normally going around a track, the suspension is working with what ever spring rate you are running (resulting in some wheel rate). When you run out of travel and fully collapse a shock with no bump stop, your spring rate (and therefore wheel rate) goes to infinity. Infinity is a very high spring rate indeed and is the least compliant you can get. Tires do not like to stick to the ground when there is no compliance. This situation does nothing good for handling. When a bump stop is in place, rather than an immediate spring rate to infinity transition; there will be a progressive ramping up of the spring rate. This is much more forgiving on the suspension and chassis and results in much more predictable handling.
Bump stops do wear out over time. The life is going to be determined mainly by the environment in which they live. Severe weather and track use will accelerate degradation and wear. Miles are pretty much irrelevant unless your car is "stanced bro" and you are riding on the bumpstops constantly. Evidence of this can be seen on a car we currently have in the shop. It is a 2006 Lotus Elise with 14,000 miles on it. Luckily this customer is getting a nice set of Nitron 40mm Single Adjustable Dampers to replace these tired units.
|This is not an effective bump stop...|
Tuesday, November 8, 2016
Brainstorming A Solution
Getting a bar into the Alfa presented some challenges as the chassis and seats did not give us much latitude. We've designed harnessbars for over 10yrs for Lotus Elise/Evora and Mini Coopers. Some of our design requirements for the 4C included: be economical, 100% reversible, require minimal modification, and most importantly, be safe. Safe means it must be strong AND correctly position the shoulder belts. Solutions we've seen in various cars, including the 4C, position shoulder belts too high. After MUCH head scratching and going through a number of concepts, we landed on the one you see for sale today. We hit our targets for safety and reversibility.
|Joe (our engineer) earning his paycheck.|
|Prototype bar in place. It fit our car!|
Great! Right? Well, when dealing with these low volume cars, sometimes it is difficult to get your hands on a single car for testing, much less multiple cars. Before production, we identified a potential issue. We assumed there would be some variation in the distance between the seat belt mounting points that the bar bolts to. We did some estimation that the variation would be 1/8" or less which the bar was designed to deal with. We were wrong. After we started selling our bar, we found out we were wrong. It turns out the variation from car to car is more. This may be due to the introduction of a new model called the 4C Spider - though we are not sure. Regardless, small volume cars generally have much more car to car variability and that must be considered in the design of any hard parts.
We needed to get creative again and come up with a solution to take up the car to car variation. Our current bar fit some Coupes but not Spiders (2 so far). Most cars have 'slip joints' to take up build tolerances. This gave us an idea. We decided that the best way to allow the bar to accommodate the width variation is to allow it to telescope. We brainstormed several different approaches to make this happen and finally landed on a solution. Obviously safety was critical and we are happy that it is probably now even stronger than before.
Our solution is a slug and sleeve arrangement to give the bar some telescope ability in the width direction. We cut the bar in half, insert and bond a slug inside the tube and slid a sleeve over the top. This sleeve is also bonded to one side of the 4Corsa. The other side of the 4Corsa bar slides into this joint. This arrangement is total overkill. The slug in the center is a piece solid steel round bar and the sleeve, being bigger than the tube it is covering, is even stronger. The both of these parts combine make sure that the bar is not any weaker than the original design. We came up with the acronym, TSSJ (Telescopic Slug Sleeve Joint) because necessity is the mother of all invention and why shouldn't we have some fun at the same time?!
Section view of slug and sleeve retrofit.
Slug is red, sleeve is blue, original tube is grey.
Thursday, October 27, 2016
In a recent blog, we mentioned the merits of good practices when plumbing or wiring a modified car but the safety aspect needs to be addressed as well. Fuel and oil lines are not places to save money on cheaper parts, they are not places to save time while building, and attention needs to be paid to how these systems are routed and secured. Too many times have we found loose oil or fuel lines in a vehicle that were about to cause an issue. We even had a problem during our Drakan testing when an OEM fuel connector came off the hard line it was attached to because too much movement was allowed. A simple ziptie fixed any future problem.
Below is an example of what a fuel fire can look like inside a car. This video shows the speed at which a fuel fire can start, the importance of safety gear (it is not all created equally by the way) and the importance of practicing getting out of your car in an emergency. While we do not know the cause of the fuel fire in this vehicle, it is a very eye opening look at the seriousness of a fuel fire, no matter the cause.
This is especially relevant to the Lotus Elise and Exige community because the design of the stock fuel tank allows the engine to be fuel starved in left hand turns when low on fuel. In our opinion, there are two ways to safely take care of this issue.Scary moment today as my car caught on fire after a fuel leak. Lucky to walk away and most importantly I am okay, with only a few blisters. pic.twitter.com/Q8MunMyuK2— Ben Waddell (@BenWaddell) October 23, 2016
- Keep your tank topped up.
- Use a baffled fuel tank like our V2 Tank .
Here another video of a Lotus Exige on fire:
Here is less alarming (actually quite funny) video from another fire. This one is more likely oil related than fuel, but the lessons still apply.
So please remember:
- Pay attention when modifying fuel, oil, or wiring systems.
- Wear your safety gear!